Confirm carrier compatibility
Provide the tractor, skid-steer loader or excavator model, rated power or operating weight, and the required working width.
LAND CLEARING AND VEGETATION MANAGEMENTRequest a quote: AN-FM Series →Chat with Sales EngineerRead Operating Instructions ↓
Land Clearing Machine and Forestry Mulcher
A configurable forestry mulcher attachment for clearing overgrown fields, orchard grass, dense weeds, brush and crop residue. Tractor-mounted models use a rear three-point hitch and PTO or hydraulic drive; hydraulic versions can also be matched to skid-steer loaders and excavators.
Technical overview
ModelAN-FM Series
Compatible carriersTractor / skid-steer loader / excavator
Tractor power30 HP and above; model dependent
Working width0.8-2.4 m; customizable by model
Mounting systemThree-point hitch Category I / II / III or carrier-specific mounting plate
Tractor PTO speed540 rpm preferred / 720 rpm where compatible
Rotor speedApprox. 1,800-2,400 rpm
Working depthApprox. 0-8 cm for surface vegetation mulching
Cutting systemFixed knife or hammer-style rotor; model dependent
Drive optionsPTO shaft or hydraulic drive
Cutting-tool materialD2 alloy; supplied reference tool approx. 623.7 g
Rotor and bearingsQ355 rotor shaft / NSK bearings; selected-model confirmation required
Engineering advantages
Practical machine advantages
Working widths from approximately 0.8 to 2.4 m can be matched to the carrier and field requirement.
PTO-driven tractor models and hydraulic skid-steer or excavator versions cover different operating fleets.
Fixed-knife or hammer-style rotors mulch grass, weeds, brush and crop residue into material left on the ground.
Protective chains and guarded drive components help control flying debris and reduce access to moving parts.
D2 alloy cutting tools, a Q355 rotor shaft and NSK bearings are available according to the selected configuration.
Carrier horsepower, hydraulic flow, pressure, hitch interface and rotor layout are confirmed before production.
Operating instructions
Recommended operating flow
Follow the supplied machine manual and your farm safety rules. Confirm the ordered configuration before operation.
Connect and inspect
Secure the hitch or mounting plate, connect the guarded PTO or hydraulic lines, and inspect cutting tools, fasteners and protection components.
Perform a no-load test
Run the rotor briefly at a safe height and check for abnormal noise, vibration, oil leakage or interference.
Mulch at a controlled speed
Lower the machine to the recommended height and move steadily according to vegetation density, ground condition and carrier capacity.
Before starting
- Inspect guards, fasteners and working components.
- Confirm fuel, power or tractor connection as applicable.
- Clear people and obstacles from the work area.
Safety essentials
- Only trained personnel should operate the machine.
- Stop and isolate power before clearing a blockage.
- Keep bystanders away from moving and discharge parts.
Daily maintenance
- Remove residual material after each shift.
- Inspect wear parts, hoses and fasteners regularly.
- Lubricate and service the machine according to the manual.
Working videos
See the machine in action
Review the product footage to understand the machine layout and operating process. Confirm the exact configuration shown before ordering.
Watch on YouTube →Land Clearing Machine and Forestry Mulcher
Land Clearing Machine and Forestry Mulcher
Land Clearing Machine and Forestry Mulcher
Land Clearing Machine and Forestry Mulcher
Land Clearing Machine and Forestry Mulcher
Before ordering
Information needed to match your configuration
Compatible carriers
Tractor power
Working requirement
Destination country
Specification
| Parameter | Value |
|---|---|
| Model | AN-FM Series |
| Compatible carriers | Tractor / skid-steer loader / excavator |
| Tractor power | 30 HP and above; model dependent |
| Working width | 0.8-2.4 m; customizable by model |
| Mounting system | Three-point hitch Category I / II / III or carrier-specific mounting plate |
| Tractor PTO speed | 540 rpm preferred / 720 rpm where compatible |
| Rotor speed | Approx. 1,800-2,400 rpm |
| Working depth | Approx. 0-8 cm for surface vegetation mulching |
| Cutting system | Fixed knife or hammer-style rotor; model dependent |
| Drive options | PTO shaft or hydraulic drive |
| Cutting-tool material | D2 alloy; supplied reference tool approx. 623.7 g |
| Rotor and bearings | Q355 rotor shaft / NSK bearings; selected-model confirmation required |
Full product gallery
Machine details, loading & working views
Select any image to open a larger view.
Factory to destination
Prepared for export, backed by our factory.
Packing, documentation and export preparation are coordinated before dispatch so your team receives the ordered machine ready for the job.
Export packing
Protective crating and organised loading for international shipment.
Factory production
Assembly and configuration support from the Anlan production base.
Product enquiry
Get a configuration and export quote.
Tell us where the machine will work, your target capacity and destination country. We will confirm the configuration and shipping details.